Thursday, December 13, 2012

DIY Unique charm earrings

How to make your own unique charm earrings



   
Materials needed:

  • jewelry charms (any light weight charms you like)
  • jump rings 
  • earring hooks
  • pliers
  • wire cutters (side cutters)
  • Round nose pliers ( small pliers)
All items were purchased at Michael's Arts and Craft Store
Pliers & Wire cutters- Unknown Brand
Charms- Bead Landing


Jump Ring & Earring Hooks- Industrial Chic
LETS BEGIN!

STEP ONE:Pick out which charms you would like to use and make sure you have double of the same one. Match the color of the charm to the color of the jump rings and earring hooks.



STEP TWO:Using your pliers open one of the jump rings slightly and slide one of the charms on to it. At this point you can choose if you would like to add chains or any other charms on to the ring. 



STEP THREE:After you are done with placing your desired charms on to the jump ring, attach it to the ring at the bottom of the earring hook and seal the jump ring back up with your pliers.

Seal it up



STEP FOUR: And TA DA! You're done!


Very easy yes i know ha ha, but this quick and easy project can make great gifts for friends and family for the holidays, birthdays, or any special occasion. 

Hope You Enjoyed and Try it for yourself :)


Friday, December 7, 2012

<a href="http://www.bloglovin.com/blog/4352175/?claim=vdfbrc6z7np">Follow my blog with Bloglovin</a>

Thursday, December 6, 2012

DIY Distressed Denim Vest

 

How to create your very own distressed denim vest.

Things you will need:

Jean Jacket (or Denim shirt)
Scissors
Marking pencil
Ruler
Pliers
Washing machine and dryer

Extra things you may need:

Chains ( of different widths,sizes, and styles)
Jump rings
Wire/Chain cutter


STEP ONE: Lay your Jean jacket (or denim shirt) on a flat surface and begin to cut the sleeves off of both sides.



could leave it just like this, but why not go farther?
 

STEP TWO: Take a ruler or straight edge and marking pencil, and mark where you would like the placement of your distressed cuts and holes to be. After making your marks cut along those exact lines.
Make sure your markings are at least 1/4 to 1/2 inches apart

STEP THREE: Once your slits have been made, take your scissors and start to run them vertically down the slits to rough them up.


 
 STEP FOUR:  Take your scissors and begin to run them up and down over the arm holes until you have reached your desired frayed look.     
left: not frayed      Right: slightly frayed

STEP FIVE: Avoiding the seams holding the vest together, cut the very edge of the bottom of the vest and begin to fray that as well with the scissors.
cutting the edges off *snip snip snip
fraying the edges
 

STEP SIX: After you have roughed up and deconstructed your vest to your liking, put it into the washer and dryer to deconstruct it a little bit more. (You do not have to do this step if you are already pleased with what you already have created.)
                                              
 
STEP SEVEN: After removing your vest from the dryer it should look more distressed and shredded than before. After wards you can pull more horizontal strings from the slits you made. After completing these steps you are pretty much complete with your distressed vest, but if you want to go further with this project you can add chains or studs to your vest.






pulling on the horizontal threads more



AFTERWARDS


EXTRA STEPS*
 

STEP EIGHT: Get three chains of different lengths and widths and a jump ring. Puncture the fabric (wherever you would like to place your chains) with the jump ring, add the chains, and close the ring with a pair of pliers.

 
should look somewhat like this
 

STEP NINE: Measure out how long you want your chains to be and cut the excess off with either wire cutters or scissors, or remove the excess by opening the chains with your pliers and sliding the excess off. 
 
STEP TEN: After cutting off the excess chains repeat STEP EIGHT and you are complete!
 
THE FINISHED PRODUCT!

Hope You Enjoyed and Try it out yourself!